allgosts.ru01. ОБЩИЕ ПОЛОЖЕНИЯ. ТЕРМИНОЛОГИЯ. СТАНДАРТИЗАЦИЯ. ДОКУМЕНТАЦИЯ01.040. Словари

ГОСТ 28500-90 Передачи ременные синхронные. Термины и определения

Обозначение:
ГОСТ 28500-90
Наименование:
Передачи ременные синхронные. Термины и определения
Статус:
Действует
Дата введения:
06.30.1991
Дата отмены:
-
Заменен на:
-
Код ОКС:
01.040.21, 21.220.10

Текст ГОСТ 28500-90 Передачи ременные синхронные. Термины и определения


ГОСТ 28500-90
(ИСО 5288-82)

Группа Г00



МЕЖГОСУДАРСТВЕННЫЙ СТАНДАРТ

ПЕРЕДАЧИ РЕМЕННЫЕ СИНХРОННЫЕ

Термины и определения

Synchronous belt drives. Terms and definitions


МКС 01.040.21
21.220.10
ОКСТУ 0090; 4101

Дата введения 1991-07-01



ИНФОРМАЦИОННЫЕ ДАННЫЕ

ВНЕСЕН Министерством нефтеперерабатывающей и нефтехимической промышленности СССР

Постановлением Государственного комитета СССР по управлению качеством продукции и стандартам от 30.03.90 N 721 введен в действие государственный стандарт ГОСТ 28500-90, в качестве которого непосредственно применен международный стандарт ИСО 5288-82 с 01.07.91

ПЕРЕИЗДАНИЕ. Октябрь 2005 г.

1. ОБЪЕКТ И ОБЛАСТЬ ПРИМЕНЕНИЯ

Настоящий стандарт устанавливает термины и определения понятий в области синхронных ременных передач.

Термины, установленные настоящим стандартом, обязательны для применения во всех видах документации и литературы, входящих в сферу работ по стандартизации или использующих результаты этих работ.

В таблице приведены термины с определениями на трех официальных языках ИСО - русском, английском и французском.

В таблице к ряду терминов приведены буквенные обозначения и чертежи.

В стандарте приведены алфавитные указатели содержащихся в нем терминов на английском, французском и русском языках. Кроме того, в качестве справочных приведены алфавитные указатели терминов-эквивалентов на немецком и итальянском языках.

Термины и определения, относящиеся к синхронным ременным передачам



Таблица

Термин

Обозна-
чение

Определение

Чертеж

2 General definitions



Общие определения

2.1 synchronous belt drive

A system composed of a synchronous belt and two or more synchronous pulleys. Synchronized motion and/or power is transmitted through the engagement of teeth on the belt with teeth on the pulleys

transmission par courroie synchrone

d'une courroie synchrone et d'au moins deux poulies synchrones. La rotation ou la puissance est transmise par des dents de la courroie avec celles des poulies

синхронная ременная передача

Передача, состоящая из синхронного ремня и не менее двух синхронных шкивов; мощность или вращение передаются посредством зацепления зубьев ремня с зубьями шкивов

2.2 centre distance

The shortest distance between the axes of two synchronous pulleys when the belt is under the prescribed measuring force

entr'axe

Plus courte distance entre les axes de deux poulies synchrones lorsque la courroie supporte l'effort de mesure prescrit

межосевое расстояние

Самое короткое расстояние между осями двух синхронных шкивов, когда ремень находится под требуемым натяжением

3 Definitions relating to synchronous belts

concernant les courroies synchrones

Определения, относящиеся к синхронным ремням

3.1 Belts, general

Courroies,

Ремни, общая часть

3.1.1 synchronous belt

A belt, the cross section of which is in the general form of a rectangle, but with transverse teeth extending from the lower base at regularly spaced intervals

courroie synchrone

Courroie dont la section droite la forme d'un rectangle mais qui comporte des intervalles des dents transversales sous sa face

синхронный ремень

Ремень, прямое сечение которого имеет форму прямоугольника, на внутренней стороне которого расположены на равном расстоянии друг от друга поперечные зубья трапециевидного профиля

3.1.2 belt pitch

The linear distance between the axes of two consecutive teeth in a section of belt loaded to the prescribed measuring force

pas

Distance entre les axes de de deux dents dans une portion rectiligne de courroie supportant l'effort prescrit de mesure

шаг

Расстояние между осями симметрии двух последовательных зубьев на прямолинейном участке ремня, находящемся под заданным натяжением

3.1.3 pitch line

Any circumferential line in the belt which keeps the same length when the belt is bent perpendicularly to its base

ligne primitive

Toute ligne de courroie qui conserve sa longueur lorsque la courroie est perpendiculairement sa base

расчетная линия

Любая круговая линия ремня, сохраняющая свою длину, когда ремень сложен перпендикулярно к основанию

3.1.4 pitch length longueur primitive

The length of the pitch line of a belt Longueur de la ligne primitive d'une courroie

расчетная длина

Развернутая длина расчетной линии ремня

3.1.5 width

The transverse dimension of the belt that can be used to transmit power

largeur

Dimension transversale de la courroie dont la puissance transmissible

ширина

Поперечный размер ремня, от которого зависит передаваемая мощность

3.1.6 height

The total height of the belt

hauteur

Hauteur ou totale de la courroie

высота

Высота или общая толщина ремня

3.2 Synchronous belt teeth

Dents de courroie synchrone

Зубья синхронного ремня

3.2.1 tooth

One of the transverse elements protruding from the bottom of the belt having the profile to mesh with the teeth in a synchronous pulley

dent

Un des transversaux faisant saillie sous la face de la courroie et ayant Ie profil pour engrener avec les dents d'une poulie synchrone

зубья

Поперечные элементы, расположенные на внутренней поверхности ремня, для сцепления с зубьями синхронного шкива

3.2.2 tip line

Line joining the apices of the belt teeth

ligne de

Ligne joignant les sommets de dents d'une courroie l'ахе longitudinal de celle-ci

верхняя линия

Линия, соединяющая вершины зубьев ремня параллельно его продольной оси

3.2.3 root line

Line joining the low points between the teeth of a belt

ligne de pied

Ligne joignant les bases de dents d'une courroie l'axe longitudinal de celle-ci

нижняя линия

Линия, соединяющая основания зубьев ремня параллельно его продольной оси

3.2.4 tooth height

Distance between the tip line and the root line

hauteur de dent

Distance comprise entre une ligne de et une ligne de pied pour une courroie, ces deux lignes dans la section droite longitudinale de la courroie

высота зубьев

Расстояние между верхней и нижней линиями одного зуба, расположенными на одном и том же продольном прямом сечении ремня

3.2.5 flank

Area defined by the width of the belt and the straight portion of the tooth section contained between the tip line and the root line

flanc

Surface par la largeur de la courroie et la partie rectiligne de la dent comprise entre la ligne de et la ligne de pied

боковая поверхность

Участок, образующийся между внутренней и наружной поверхностями

3.2.6 mating flank

Flank of the belt tooth that is in contact with the pulley tooth

flanc en contact

Celui des deux flancs de la dent d'une courroie qui touche une dent de poulie

боковая контактирующая поверхность

Боковая поверхность зуба ремня, которая соприкасается с зубом шкива

3.2.7 working flank

Flank of a belt tooth used to transmit motion to or from the pulley

flanc actif

Celui des deux flancs d'une dent de courroie qui recoit Ie mouvement ou Ie transmet une poulie

активная боковая поверхность

Та из двух боковых поверхностей зуба ремня, которая передает движение шкиву или принимает от шкива

3.2.8 non-working flank

Flank of tooth opposite the working flank

flanc inactif

Flanc d'une dent de courroie au flanc actif

неактивная боковая поверхность

Другая боковая поверхность того же зуба

3.2.9 radius at tooth tip

Radius of a curve connecting the tooth flank with the tip line

rayon en de dent

Rayon de l'arrondi reliant la section d'un flanc de dent sa ligne de

радиус в верхней части зуба

Радиус закругленной части, соединяющий сечение боковой поверхности зуба с его верхней линией

3.2.10 radius at tooth root

Radius of a curve connecting the tooth flank witn the root line

rayon au pied de dent

Rayon de l'arrondi reliant la section d'un flanc de dent sa ligne de pied

радиус у основания зуба

Радиус закругленной части, соединяющей сечение боковой поверхности зуба с его нижней линией

3.2.11 width at tooth root

Linear distance between the theoretical points of intersection of the tooth flanks with the root line when the belt is straight

largeur au pied de dent

Distance comprise entre les points d'intersection des flancs d'une dent avec sa ligne de pied, lorsque la portion de la courroie est rectiligne

ширина у основания зуба

Расстояние между теоретическими точками пересечения боковых поверхностей зуба с его нижней линией, когда рассматриваемый участок ремня прямолинейный

3.2.12 tooth angle

2

Included angle between the flanks of the belt tooth

angle de dent

Angle compris entre les deux flancs d'une dent de courroie

угол зуба

Угол между обеими боковыми поверхностями зуба ремня

4 Definitions relating to synchronous pulleys

concernant les poulies synchrones

Определения, относящиеся к синхронным шкивам

4.1 Pulleys, general

Poulies,

Шкивы, общая часть

4.1.1 synchronous pulley

Pulley with transverse teeth equally spaced around its circumference

poulies synchrone

Poulie munie sa de dents transversales

синхронный шкив

Шкив, имеющий на своей окружности поперечные равноотстоящие зубья

4.1.2 pitch reference cylinder

Imaginary cylindrical surface, coaxial to a pulley, with reference to which the dimensions of the tooth space of a pulley are defined

cylindre primitif

Cylindre de fictif, coaxial la poulie, et servant les cotes des dents de la poulie et de leurs intervalles

расчетная цилиндрическая поверхность

Воображаемая цилиндрическая поверхность, соосная со шкивом и служащая для определения размеров зубьев шкива и расстояния между ними*

________________

* См. 4.2.2 для определения расстояния между зубьями.

4.1.3 pitch circle

Section of a pitch reference cylinder with a plane perpendicular to the axis of the pulley

cercle primitif

Section du cylindre primitif par un plan perpendiculaire l'axe de la poulie

расчетная окружность

Сечение расчетной поверхности с плоскостью, перпендикулярной к оси шкива

4.1.4 outside diameter

Diameter of the tip circle

du cercle de

наружный диаметр

Диаметр верхней окружности*

________________

* Cм. 4.2.4 для определения верхней окружности.

4.1.5 pitch diameter

Diameter of the pitch circle

primitif

du cercle primitif

расчетный диаметр

Диаметр расчетной окружности

4.1.6 pitch line differential

Radial distance between the pitch circle and the tip circle

de ligne primitive

Distance suivant un rayon entre Ie cercle primitif et Ie cercle de

положение расчетной линии

Расстояние, измеренное по радиусу между расчетной окружностью и верхней окружностью

4.1.7 pitch

Length of arc on the pitch circle contained between two consecutive corresponding profiles

pas

Longueur Ie l'arc du cercle primitif compris entre les points homologues de deux dents

шаг*

Длина дуги расчетной окружности между соответствующими точками двух последовательных зубьев

________________

* Рассматриваемый как отрезок зубчатой рейки, шаг шкива соответствует шагу ремня.

4.1.8 minimum pulley width


Smallest lateral distance across the face of a pulley (or between the flanges of a flanged pulley) that can be used for a stated belt width

largeur minimale de poulie

Plus petite distance axiale entre les deux faces d'une poulie, ou entre les flasques d'une poulie , qui puisse pour une courroie de largeur

минимальная ширина

Наименьшее осевое расстояние между обеими поверхностями шкива или между фланцами шкива, которое может быть использовано для ремня заданной ширины

4.1.9 measuring pulley

Pulley specifically machined or selected to permit precise length measurement of a synchronous belt

poulie de mesure

Poulie ou choisie pour permettre de mesurer avec la longueur d'une courroie synchrone

измерительный шкив

Изготовленный или специально подобранный шкив для прецизионного измерения длины синхронного ремня

4.1.10 measuring pulley tooth clearance

Shortest distance between nonworking flanks of belt and measuring pulley teeth, when the working flanks are in contact

jeu de denture sur la poulie de mesure

Plus petite valeur de la distance les flancs inactifs d'une dent de la courroie et de la dent voisine de la poulie, lorsque les flancs actifs sont en contact l'un avec l'autre

зубчатый зазор на измерительном шкиве

Наименьшее расстояние, разделяющее неактивные боковые поверхности зуба ремня и зуба шкива, когда активные боковые поверхности контактируют друг с другом

4.2 Synchronous pulley teeth

Dents de poulie synchrone

Зубья синхронного шкива

4.2.1 teeth

Equally spaced transverse protrusions with which the belt teeth mesh to provide a transfer of force between the belt and the pulley

dents

transversaux
qui font saillie la d'une poulie et avec lesquels les dents d'une courroie pour transmettre un effort tangential de l'une l'autre

зубья

Равностоящие поперечные элементы, выступающие на окружности шкива, с которыми зубья ремня образуют зацепление для передачи тангенциального усилия

4.2.2 tooth space

Space between two adjacent teeth of a pulley

intervalle

Intervalle entre deux dents d'une poulie

пространство между зубьями

Расстояние между двумя последовательными зубьями шкива

4.2.3 tip cylinder

Surface coaxial with the pulley containing the crests of the teeth

cylindre de

Surface coaxiale a la poulie et contenant les sommets ou de dents

верхняя цилиндрическая поверхность

Поверхность, соосная со шкивом на уровне вершин зубьев

4.2.4 tip circle

Section of the tip cylinder whose plane is perpendicular to the axis of the pulley

cercle de

Section droite du cylinder de

верхняя окружность

Прямое сечение верхней цилиндрической поверхности

4.2.5 root cylinder

Surface coaxial with the pulley containing the bottom of the tooth spaces

cylindre de pied

Surface coaxiale la poulie et tangente au fond des intervalles

нижняя цилиндрическая поверхность

Поверхность, соосная со шкивом и касательная к основанию зубьев

4.2.6 root circle

Section of the root cylinder whose plane is perpendicular to the axis of the pulley

cercle de pied

Section droite du cylindre de pied

нижняя окружность

Прямое сечение нижней цилиндрической поверхности

4.2.7 tooth space depth

Radial distance between the tip circle and the root circle

profondeur de I'intervalle

Dimension Ie long d'un rayon entre un cercle de et un cercle de pied dans Ie plan

глубина пространства между зубьями

Расстояние, определяемое по радиусу между верхней и нижней окружностями, расположенными в одной плоскости

4.2.8 flank

Area defined by the width of the pulley and the involute (or straight) portion of a pulley tooth contained between the tip cylinder and the root cylinder

flanc

Une des surfaces par la largeur de la poulie et par la partie en de cercle (ou rectiligne) de la dent qui est comprise entre Ie cylinder de et Ie cylindre de pied

боковая поверхность

Одна из поверхностей, ограниченных шириной шкива и верхней и нижней поверхностями цилиндра (или прямолинейными участками)

4.2.9 mating flank

Flank of the pulley tooth that is in contact with the belt

flanc en contact

Flanc d'une dent de poulie qui touche une dent de courroie

боковая контактирующая поверхность

Боковая поверхность зуба шкива, соприкасающаяся с зубом ремня

4.2.10 working flank

Flank of the pulley tooth used to transmit motion to or from the belt

flanc actif

Flanc d'une dent de poulie qui
Ie mouvement ou Ie transmet la courroie

активная боковая поверхность

Боковая поверхность зуба шкива, передающая движение ремню или принимающая его

4.2.11 non-working flank

Flank of the pulley tooth opposite the working flank

flanc inactif

Flanc d'une dent de poulie au flanc actif

неактивная боковая поверхность

Другая боковая поверхность того же зуба

4.2.12 radius at the tooth tip

Radius of a curve connecting the tooth flank with the tip circle

rayon en de dent

Rayon de l'arrondi reliant la section d'un flanc de dent a sa ligne de

радиус у вершины зуба

Радиус закругления, соединяющего сечение боковой поверхности зуба с верхней окружностью

4.2.13 radius at the tooth root

Radius of a curve connecting the tooth flank with the root circle

rayon au pied de dent

Rayon de l'arrondi reliant la section d'un flanc de dent sa ligne de pied

радиус у основания

Радиус закругления, соединяющего сечение боковой поверхности зуба с нижней окружностью

4.2.14 width at tooth space root

Linear distance between the theoretical points of intersection of the tooth space flanks with the root circle

largeur au pied de dent

Distance suivant une corde entre les points d'intersection du cercle de pied avec les flancs, se faisant face, de deux dents

ширина основания зуба

Расстояние, измеренное по хорде между теоретическими точками пересечения нижней окружности с боковыми поверхностями, расположенными напротив двух соседних зубьев

4.2.15 tooth space angle

2

Included angle between the flanks of the tooth space

angle au sommet de l'intervalle

Angle compris entre les flancs, se faisant face, de deux dents

угол пространства между зубьями

Угол между боковыми поверхностями двух соседних зубьев

4.3 Synchronous pulley involute tooth generating tools

de pour dents de poulie en

Стандартная кремальера для зубьев шкива в развертке

4.3.1 rack

Toothed member having the form of a rectangular bar, whose teeth may be superimposed by rectilinear translation

Organe de forme
, et portant sur

une de ses faces une de dents superposables par translation rectiligne

кремальера

Элемент в форме параллелепипеда, несущий на одной из своих поверхностей ряд одинаковых равноотстоящих зубьев

4.3.2 reference rack

Rack whose profile is used as the base of a standardized system of pulleys having the same generating rack

de

dont la section perpendiculaire aux des dents sert les dimensions des dents en d'un de poulies

эталонная кремальера

Вымышленная кремальера, сечение которой перпендикулярно к ребрам зубьев и служит для определения нормализованных размеров зубьев в развертке той же системы шкивов

4.3.3 reference rack: pitch line

Line, with reference to which the dimensions of the rack teeth are defined

ligne primitive de la
de

Ligne par rapport a laquelle sont les dimensions des dents de la de

расчетная линия эталонной кремальеры

Линия, по отношению к которой определяются размеры зубьев эталонной кремальеры

4.3.4 reference rack: root line

Line joining the low points between the teeth of a rack

ligne de pied de la

de

Ligne reliant les fonds des dents d'une section longitudinale de la

нижняя линия эталонной кремальеры

Линия, соединяющая поверхности кремальеры, расположенные между зубьями, в продольном сечении эталонной кремальеры

4.3.5 reference rack: tip line

Line joining the tips of the teeth of a rack

ligne de de la de

Ligne reliant les des dents d'une section longitudinale

de la

верхняя линия эталонной кремальеры

Линия, соединяющая верхние поверхности зубьев, в продольном сечении эталонной кремальеры

4.3.6 reference rack: flank

Portion of the rack tooth contained between the tip line and the root line

flanc d'une dent de la
de

Partie d'une dent de la
de qui est comprise entre la ligne de

et la ligne de pied

боковая поверхность зуба эталонной кремальеры

Часть зуба эталонной кремальеры между уровнем верхней и нижней линии

4.3.7 reference rack: pitch line location

Distance between the pitch line and the root line of the rack

de la ligne primitive de la de

Distance comprise entre la ligne primitive de la de et sa ligne de pied

расположение расчетной линии эталонной кремальеры

Расстояние между расчетной линией эталонной кремальеры и нижней линией

4.3.8 reference rack: pitch

Linear distance between the centre of two adjacent teeth on the rack

pas de la de

Distance comprise entre les axes de de deux dents de la

de

шаг эталонной кремальеры

Расстояние между осями симметрии двух последовательных зубьев эталонной кремальеры

4.3.9 reference rack: tooth angle

2

Included angle between the flanks of the tooth of the rack

angle de la dent de la
de

Angle par les deux flancs d'une dent de la
de

угол у вершины зуба эталонной кремальеры

Угол между двумя боковыми поверхностями зуба эталонной кремальеры

4.3.10 reference rack: tooth height

Distance between the tip line and the root line of the rack

hauteur de dent de la
de

Distance comprise entre une ligne de et une ligne de pied dans la section droite longitudinale de la
de

высота зуба эталонной кремальеры

Расстояние между верхней и нижней линиями, расположенными в одном и том же прямом продольном сечении эталонной кремальеры

4.3.11 reference rack: width at tooth tip

Linear distance between the theoretical points of intersection of the tooth flanks with the tip line of the rack

largeur en de dent de la de

Dans une section droite longitudinale de la de , distance comprise entre les points d'intersection des flancs d'une dent avec la ligne de

ширина в верхней части зуба эталонной кремальеры

Расстояние между теоретическими точками пересечения боковых поверхностей зуба с верхней линией в прямом продольном сечении кремальеры

4.3.12 reference rack: radius at tooth tip

Radius of a curve connecting the tooth flank with the tip line of the rack

rayon en d'une dent de la de

Dans une section droite longitudinale de la de , rayon de l'arrondi reliant un flanc de dent la ligne de

радиус в верхней части зуба эталонной кремальеры

Радиус закругления, соединяющего боковую поверхность зуба с верхней линией в прямом продольном сечении эталонной кремальеры

4.3.13 reference rack: radius at tooth root

Radius of a curve connecting the tooth flank with the root line of the rack

rayon au pied d'une dent de la de

Dans une section droite longitudinale de la de , rayon de l'arrondi reliant un flanc de dent la ligne de pied

радиус у основания зуба эталонной кремальеры

Радиус закругления, соединяющего боковую поверхность зуба с нижней линией в прямом продольном сечении эталонной кремальеры



АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА АНГЛИЙСКОМ ЯЗЫКЕ

В

Belt pitch

3.1.2

Belts

3.1

С

Centre distance

2.2

F

Flank

3.2.6, 4.2.8

Н

Height

3.1.6

М

Mating flank

3.2.6, 4.2.9

Measuring pulley

4.1.9

Measuring pulley tooth clearance

4.1.10

Minimum pulley width

4.1.8

N

Non-working flank

3.2.8, 4.2.11

О

Outside diameter

4.1.4

Р

Pitch

4.1.7

Pitch circle

4.1.3

Pitch diameter

4.1.5

Pitch length

3.1.4

Pitch line

3.1.3

Pitch line differential

4.1.6

Pitch reference cylinder

4.1.2

Pulleys

4.1

R

Rack

4.3.1

Radius at tooth line

4.2.12

Radius at tooth root

3.2.10

Radius at tooth tip

3.2.9, 4.2.12

Reference rack

4.3.2

flank

4.3.6

pitch

4.3.8

pitch line

4.3.3

pitch line location

4.3.7

radius at tooth tip

4.3.12

radius at tooth root

4.3.13

root line

4.3.4

tip line

4.3.5

tooth angle

4.3.9

tooth height

4.3.10

width at tooth tip

4.3.11

Root circle

4.2.6

Root line

3.2.3

S

Synchronous belt

3.1.1

Synchronous belt drive

2.1

Synchronous pulley

4.1.1

Synchronous pulley teeth

4.2

Synchronous pulley involute tooth generating tools

4.3, 3.2

Т

Tip circle

4.2.4

Tip cylinder

4.2.3

Tip line

3.2.2

Teeth

4.2.1

Tooth

3.2.1

Tooth angle

3.2.12

Tooth height

3.2.4

Tooth space

4.2.2

Tooth space angle

4.2.15

Tooth space depth

4.2.7

W

Width

3.1.5

Width at tooth root

3.2.11

Width at tooth space root

4.2.14

Working flank

3.2.7, 4.2.10



АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА ФРАНЦУЗСКОМ ЯЗЫКЕ

А

angle au sommet de l'intervalle

4.2.15

angle de dent

3.2.12

angle de la dent de la de

4.3.9

С

cercle de pied

4.2.6

cercle de

4.2.4

cercle primitif

4.1.3

courroies

3.1

courroie synchrone

3.1.1

4.3.1

de

4.3.2

de pour dents de poulie en

4.3

cylindre de pied

4.2.5

cylindre de

4.2.3

cylindre primitif

4.1.2

D

4.1.4

primitif

4.1.5

dent (s)

3.2.1, 4.2.1

dents de courroie synchrone

3.2

dents de poulie synchrone

4.2

de ligne primitive de la de

4.3.7

de la ligne primitive

4.1.6

Е

entr'axe

2.2

F

flanc

3.2.5, 4.2.8

flanc actif

3.2.7, 4.2.10

flanc d'une dent de la de

4.3.6

flanc en contact

3.2.6, 4.2.9

flanc inactif

3.2.8, 4.2.11

H

hauteur

3.1.6

hauteur de dent

3.2.4

hauteur de dent de la de

4.3.10

I

intervalle

4.2.2

J

jeu de denture sur la poulie de mesure

4.1.10

L

largeur

3.1.5

largeur au pied de dent

3.2.10, 4.2.14

largeur en de dent de la de

4.3.11

largeur minimale de poulie

4.1.8

ligne de pied

3.2.3

ligne de pied de la de

4.3.4

ligne de

3.2.2

ligne de de la de

4.3.5

ligne primitive

3.1.3

ligne primitive de la de

4.3.3

P

pas

3.1.2, 4.1.7

de la de

4.3.8

poulies

4.1

poulie de mesure

4.1.9

poulie synchrone

4.1.1

profondeur de l'intervalle

4.2.7

R

rayon au pied de dent

3.2.10, 4.2.13

rayon en de dent

3.2.9, 4.2.12

rayon au pied d'une dent de la de

4.3.13

rayon en d'une dent de la de

4.3.12

Т

transmission par courroie synchrone

2.1



АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА РУССКОМ ЯЗЫКЕ

зубья синхронного ремня

3.2, 3.2.1

боковая поверхность

3.2.5

боковая поверхность активная

3.2.7

боковая поверхность контактирующая

3.2.6

боковая поверхность неактивная

3.2.8

верхняя линия

3.2.2

высота зубьев

3.2.4

нижняя линия

3.2.3

радиус в верхней части зуба

3.2.9

радиус у основания зуба

3.2.10

угол зуба

3.2.12

ширина у основания зуба

3.2.11

зубья синхронного шкива

4.2, 4.2.1

боковая поверхность

4.2.8

боковая поверхность активная

4.2.10

боковая поверхность контактирующая

4.2.9

боковая поверхность неактивная

4.2.11

верхняя цилиндрическая поверхность

4.2.3

верхняя окружность

4.2.4

глубина пространства между зубьями

4.2.7

пространство между зубьями

4.2.2

радиус у вершины зуба

4.2.12

радиус у основания

4.2.13

ширина основания зуба

4.2.14

угол пространства между зубьями

4.2.15

К

кремальера

4.3.1

боковая поверхность зуба эталонной кремальеры

4.3.6

верхняя линия эталонной кремальеры

4.3.5

высота зуба эталонной кремальеры

4.3.10

нижняя линия эталонной кремальеры

4.3.4

радиус в верхней части зуба эталонной кремальеры

4.3.12

радиус у основания зуба эталонной кремальеры

4.3.13

расчетная линия эталонной кремальеры

4.3.3

расположение расчетной линии эталонной кремальеры

4.3.7

угол у вершины зуба эталонной кремальеры

4.3.9

шаг эталонной кремальеры

4.3.8

ширина в верхней части зуба эталонной кремальеры

4.3.11

эталонная

4.3.2

Р

расстояние межосевое

2.2

ремни

3

высота

3.1.6

зубья синхронного ремня

3.2

общая часть

3.1

расчетная длина

3.1.4

расчетная линия

3.1.3

синхронные

3.1.1

шаг

3.1.2

ширина

3.1.5

С

синхронная ременная передача

2.1

синхронные ремни

3

Ш

шкивы

4.1

зубчатый зазор на измерительном шкиве

4.1.10

зубья синхронного шкива

4.2

измерительный шкив

4.1.9

минимальная ширина

4.1.8

наружный диаметр

4.1.4

расчетный диаметр

4.1.5

расчетная окружность

4.1.3

расчетная цилиндрическая поверхность

4.1.2

синхронные

4.1.1



АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА НЕМЕЦКОМ ЯЗЫКЕ

А

Arbeitsflanke

3.2.7, 4.2.10

4.1.4

В

Bezugsprofil

4.3.2

Bezugszahnstange

4.3.2

Breite

3.1.5

Breite am

3.2.11

Breite am Zahnkopf

4.3.11

Breite am

4.2.14

F

Flanke

3.2.5, 4.2.8, 4.3.6

Hankenspiel in der

4.1.10

4.2.6

3.2.3, 4.3.4

4.2.5

G

Gegenflanke

3.2.6, 4.2.9

H

3.1.6

К

Kopfkreis

4.2.4

Kopflinie

3.2.2, 4.3.5

Kopfzylinder

4.2.3

L

Lage der Wirklinie

4.3.7

M

4.1.9

Mittenabstand

2.2

R

Radius am

3.2.10, 4.2.13, 4.3.13

Radius am Zahnkopf

3.2.9, 4.2.12, 4.3.12

Riemen

3.1

Riemenzahnteilung

3.1.2

3.2.8, 4.2.11

S

Scheibe

4.1

Scheibenbreite, Mindest

4.1.8

Synchronriemen

3.1.1

Synchronriementrieb

2.1

Synchronscheibe

4.1.1

Т

Teilung

4.1.7, 4.3.8

Teilungs-Bezugszylinder

4.1.2

W

Wirkdurchmesser

4.1.5

Wirkkreis

4.1.3

3.1.4

Wirklinie

3.1.3, 4.3.3

Wirklinien-Differenz

4.1.6

Z

Zahn

3.2.1, 4.2.1

3.2.4, 4.3.10

4.2.2

4.2.7

4.2.15

Zahnstange

4.3.1

Zahnteilung

3.1.2, 4.1.7

Zahnwinkel

3.2.12, 4.3.9



АЛФАВИТНЫЙ УКАЗАТЕЛЬ ТЕРМИНОВ НА ИТАЛЬЯНСКОМ ЯЗЫКЕ

А

altezza

3.1.6

altezza del dente

3.2.4, 4.3.10

angolo del dente

3.2.12, 4.3.9

angolo del vano

4.2.15

С

cerchio di fondo

4.2.6

cerchio di troncatura

4.2.3, 4.2.4

cilindro di fondo

4.2.5

cilindro primitivo di riferimento

4.1.2

cinghie,

3.1

cinghia sincrona

3.1.1

circonferenza primitiva

4.1.3

cremagliera

4.3.1, 4.3.2

D

dente

3.2.1, 4.2.1

dentatura cinghia sincrona

3.2

dentatura puleggia sincrona

4.2

diametro esterno

4.1.4

diametro primitivo

4.1.5

F

fianco

3.2.5, 4.2.8, 4.3.6

fianco attivo

3.2.7, 4.2.10

fianco a contatto

3.2.6, 4.2.9

fianco inattivo

3.2.8, 4.2.11

G

cremagliera di riferimento per dentatura puleggia ad evolvente

4.3

gioco nella dentatura delle puleggia di misura

4.1.10

L

larghezza

3.1.5

larghezza sul fondo del dente

3.2.11

larghezza alla del dente

4.3.11

larghezza minima

4.1.8

larghezza sul fondo del vano

4.2.14

linea di fondo

3.2.3, 4.3.4

linea di troncatura

3.2.2, 4.3.5

linea primitiva

3.1.3, 4.3.3

lunghezza primitiva

3.1.4

Р

passo

3.1.12, 4.1.7, 4.3.8

pulegge

4.1

puleggia di misura

4.1.9

puleggia sincrona

4.1.1

del vano

4.2.7

posizione linea primitiva

4.3.7

Q

quota radiale primitiva

4.1.6

R

raccordo alla del dente

3.2.9, 4.2.12, 4.3.12

raccordo sul fondo del dente

3.2.10, 4.2.13, 4.3.13

V

vano

4.2.2




Электронный текст документа
и сверен по:

, 2005